Table of Contents

Error Message

Code	Message	Note
1¶	DC5V is out of range
2¶	DC24V is out of range
5¶	Room temperature is out of range
6¶	Atm. press is out of range
7¶ 8¶ 9¶ 10¶	DET#n PCB error	n=1 to 4
11¶ 12¶ 53¶ 54¶	CARm AFC PCB error	m=1 to 4
13¶ 14¶ 15¶ 16¶	DetAPCn PCB error	n=1 to 4
23¶ 24¶ 25¶ 26¶ 27¶ 28¶	APCa-b PCB error	a-b=1-3, 4-6, 7-9, 10-12, 13-15, 16-18
29¶	Clock is initialized
30¶	COL A/D converter error
31¶	Room temp, Atm. press A/D error
32¶	AUX3-AUX5 A/D error
35¶	Cooling fan error
38¶	CPU register error
39¶	PRG current error
40¶	Power controller board error
51¶	Detected hydrogen leak
59¶ 62¶ 65¶ 68¶ 71¶ 74¶	Flow# DC24V was out of range	#=1 to 6
60¶ 63¶ 66¶ 69¶ 72¶ 75¶	Flow# DC12V was out of range	#=1 to 6
61¶ 64¶ 67¶ 70¶ 73¶ 76¶	Flow# DC5V was out of range	#=1 to 6
77¶	Hydrogen sensor init error
78¶	Hydrogen sensor is not installed
79¶	TC was broken
80¶ 81¶ 82¶ 83¶	CARx septum counter error	x=1 to 4
84¶ 85¶ 86¶ 87¶	CARx insert counter error	x=1 to 4
88¶ 89¶	AOCn syringe counter error	n=1 to 2
91¶ 92¶	Gas Selector# PCB error	#=1 to 2
100¶	Power controller board DC voltage error
101¶	Power frequency error
102¶	Intake fan error
103¶	INJ/DET heater over current error
104¶	Oven fan error
105¶	Power supply recognition error
106¶ 107¶ 108¶ 109¶	Relay Input# error	#=1 to 4
110¶	GC model recognition error
112¶	Fan for AOC-30 Dual error
113¶	Operation part fan error
116¶	Hydrogen sensor is disconnected.
117¶	Hydrogen sensor thermistor error
118¶	Oven suction pump error. Stop the instrument.
119¶	Hydrogen sensor misconfiguration error
1001¶	Heat is escaping
1002¶ 1003¶ 1004¶ 1005¶ 1006¶ 1007¶ 1008¶ 1009¶ 1053¶	xxx temperature exceeds the limit	xxx=COL, INJ1, DET1, INJ2, DET2, AUX3, AUX4, AUX5, SAT
1010¶ 1011¶ 1012¶ 1013¶ 1014¶ 1015¶ 1016¶ 1017¶ 1054¶	xxx sensor is short circuit	xxx=COL, INJ1, DET1, INJ2, DET2, AUX3, AUX4, AUX5, SAT
1018¶ 1019¶ 1020¶ 1021¶ 1022¶ 1023¶ 1024¶ 1025¶ 1055¶	xxx sensor is down	xxx=COL, INJ1, DET1, INJ2, DET2, AUX3, AUX4, AUX5, SAT
1026¶ 1027¶ 1028¶ 1029¶ 1030¶ 1031¶ 1032¶ 1033¶ 1056¶	xxx sensor error	xxx=COL, INJ1, DET1, INJ2, DET2, AUX3, AUX4, AUX5, SAT
1034¶	COL CRG is out of control
1036¶	Overheat is sensed	Overheat detected by thermocouple
1037¶ 1038¶ 1039¶ 1040¶ 1041¶ 1042¶ 1043¶ 1044¶ 1057¶	xxx temperature controller error	Overheat detected by software xxx=COL, INJ1, DET1, INJ2, DET2, AUX3, AUX4, AUX5, SAT
1045¶	COL relay error
1046¶	INJ1-DET2 relay error
1047¶	AUX3-AUX5 relay error
1049¶ 1050¶ 1051¶ 1052¶	DET#n set temperature is low	n=1 to 4
1061¶	Oven door is open
2014¶ 2017¶ 2020¶ 2023¶	DetAPCn makeup set point not reached	n=1 to 4
2015¶ 2018¶ 2021¶ 2024¶	DetAPCn hydrogen set point not reached	n=1 to 4
2016¶ 2019¶ 2022¶ 2025¶	DetAPCn air set point not reached	n=1 to 4
2026¶ 2027¶ 2028¶ 2029¶ 2030¶ 2031¶ 2032¶ 2033¶ 2034¶ 2035¶ 2036¶ 2037¶ 2038¶ 2039¶ 2040¶ 2041¶ 2042¶ 2043¶	APCy set point not reached	y=1 to 18
2048¶ 2049¶ 2050¶ 2202¶	CARx purge valve not completely closed	x=1 to 4 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2057¶ 2060¶ 2063¶ 2066¶	DetAPCn makeup valve not completely closed	n=1 to 4 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2058¶ 2061¶ 2064¶ 2067¶	DetAPCn hydrogen valve not completely closed	n=1 to 4 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2059¶ 2062¶ 2065¶ 2068¶	DetAPCn air valve not completely closed	n=1 to 4 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2069¶ 2070¶ 2071¶ 2072¶ 2073¶ 2074¶ 2075¶ 2076¶ 2077¶ 2078¶ 2079¶ 2080¶ 2081¶ 2082¶ 2083¶ 2084¶ 2085¶ 2086¶	APCy valve not completely closed	y=1 to 18 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2087¶ 2088¶ 2089¶ 2090¶	DAMCn makeup control irregularity	n=1 to 4
2091¶ 2092¶ 2093¶ 2203¶	CARn purge control irregularity	n=1 to 4
2094¶ 2095¶ 2096¶ 2097¶	DAMCn makeup control irregularity	n=1 to 4
2100¶ 2103¶ 2106¶ 2109¶	DetAPCn makeup control irregularity	n=1 to 4
2101¶ 2104¶ 2107¶ 2110¶	DetAPCn hydrogen control irregularity	n=1 to 4
2102¶ 2105¶ 2108¶ 2111¶	DetAPCn air control irregularity	n=1 to 4
2112¶ 2113¶ 2114¶ 2115¶ 2116¶ 2117¶ 2118¶ 2119¶ 2120¶ 2121¶ 2122¶ 2123¶ 2124¶ 2125¶ 2126¶ 2127¶ 2128¶ 2129¶	APCy control irregularity	y=1 to 18
2130¶ 2131¶ 2204¶ 2205¶	CARm AFC set point not reached	m=1 to 4
2132¶ 2133¶ 2206¶ 2207¶	CARm AFC valve not completely closed	m=1 to 4 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2134¶ 2135¶ 2136¶ 2137¶ 2208¶ 2209¶ 2210¶ 2211¶	CARm AFC control irregularity	m=1 to 4
2138¶ 2139¶ 2140¶ 2212¶	CARx prim is out of range	x=1 to 4
2141¶ 2142¶ 2143¶ 2213¶	CARm is not controlled	m=1 to 4
2144¶ 2145¶ 2146¶ 2147¶	DetAPCn DCG set point not reached	n=1 to 4
2148¶ 2149¶ 2150¶ 2151¶	DetAPCn DCG valve not completely closed	n=1 to 4 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2152¶ 2153¶ 2154¶ 2155¶	DetAPCn DCG control irregularity	n=1 to 4
2156¶ 2157¶ 2158¶ 2159¶	DetAPCn ECDG set point not reached	n=1 to 4
2160¶ 2161¶ 2162¶ 2163¶	DetAPCn ECDG valve not completely closed	n=1 to 4 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2164¶ 2165¶ 2166¶ 2167¶	DetAPCn ECDG control irregularity	n=1 to 4
2214¶ 2215¶ 2216¶ 2217¶	CARn was overpressure	n=1 to 4
2218¶ 2219¶ 2220¶ 2221¶	PURn was overpressure	n=1 to 4
2222¶ 2225¶ 2228¶ 2231¶	DetAPCn makeup was overpressure	n=1 to 4
2223¶ 2226¶ 2229¶ 2232¶	DetAPCn hydrogen was overpressure	n=1 to 4
2224¶ 2227¶ 2230¶ 2233¶	DetAPCn air was overpressure	n=1 to 4
2234¶ 2235¶ 2236¶ 2237¶ 2238¶ 2239¶ 2240¶ 2241¶ 2242¶ 2243¶ 2244¶ 2245¶ 2246¶ 2247¶ 2248¶ 2249¶ 2250¶ 2251¶	APCx was overpressure	x=1 to 18
2264¶ 2265¶ 2266¶ 2267¶	DetAPCn DCG was overpressure	n=1 to 4
2268¶ 2269¶ 2270¶ 2271¶	DetAPCn ECDG was overpressure	n=1 to 4
2272¶ 2273¶ 2274¶ 2275¶	DAMCn makeup set point not reached	n=1 to 4
2276¶ 2277¶ 2278¶ 2279¶	DAMCn reference set point not reached	n=1 to 4
2288¶ 2289¶ 2290¶ 2291¶	DAMCn makeup was overpressure	n=1 to 4
2292¶ 2293¶ 2294¶ 2295¶	DAMCn reference was overpressure	n=1 to 4
2296¶ 2297¶ 2298¶ 2299¶	CARn hydrogen flowing over the specified value	n=1 to 4
2300¶ 2301¶ 2302¶ 2303¶	DetAPCn hydrogen flowing over the specified value	n=1 to 4
2304¶ 2305¶ 2306¶ 2307¶ 2308¶ 2309¶ 2310¶ 2311¶ 2312¶ 2313¶ 2314¶ 2315¶ 2316¶ 2317¶ 2318¶ 2319¶ 2320¶ 2321¶	APCn hydrogen flowing over the specified value	n=1 to 18
2322¶ 2323¶ 2324¶ 2325¶ 2326¶ 2327¶	Flow# valve control irregularity	When the gas type is set to H2 for H2 carrier, H2 line of FID/FTD/FPD, H2 makeup of TCD, or AUX-APC, the instrument goes into sleep mode for safety when this error is detected. #=1 to 6
2338¶ 2339¶ 2340¶ 2341¶ 2342¶ 2343¶	Flow# press/flow offset value is shifted	#=1 to 6
2346¶ 2347¶	Gas Selector# main set point not reached	#=1 to 2
2348¶ 2349¶	Gas Selector# purge set point not reached	#=1 to 2
2350¶ 2351¶	Gas Selector# sub set point not reached	#=1 to 2
2352¶ 2353¶	Gas Selector# main valve not completely closed	#=1 to 2 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2354¶ 2355¶	Gas Selector# purge valve not completely closed	#=1 to 2 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2356¶ 2357¶	Gas Selector# sub valve not completely closed	#=1 to 2 To thoroughly check whether the valve has failed,see Diagnosis of valve failure .
2358¶ 2359¶	Gas Selector# main control irregularity	#=1 to 2
2360¶ 2361¶	Gas Selector# purge control irregularity	#=1 to 2
2362¶ 2363¶	Gas Selector# sub control irregularity	#=1 to 2
2364¶ 2365¶	Gas Selector# main was overpressure	#=1 to 2
2366¶ 2367¶	Gas Selector# purge was overpressure	#=1 to 2
2368¶ 2369¶	Gas Selector# sub was overpressure	#=1 to 2
2370¶ 2371¶	Can not switch gas because of gas selector# main error occurring	#=1 to 2
2372¶ 2373¶	Can not switch gas because of gas selector# sub error occurring	#=1 to 2
4001¶	Transmission time out	For transmission error, the link is automatically disconnected.
4003¶	Message is not accepted	For transmission error, the link is automatically disconnected.
4005¶	Command is invalid	For transmission error, the link is automatically disconnected.
4006¶	Param by TRS is out of range	For transmission error, the link is automatically disconnected.
4007¶	Transmission port is shut down	For transmission error, the link is automatically disconnected.
4008¶	Transmission file error	For transmission error, the link is automatically disconnected.
4009¶	AOC command is invalid	For transmission error, the link is automatically disconnected.
4010¶	AOC set value out of range	For transmission error, the link is automatically disconnected.
4011¶	AOC time out	For transmission error, the link is automatically disconnected.
4012¶	AOC2 transmission error	For transmission error, the link is automatically disconnected.
4013¶	AOC link error	For transmission error, the link is automatically disconnected.
4021¶ 4022¶ 4023¶ 4024¶ 4025¶ 4026¶	Flow# command stopped due to error	#=1 to 6
4045¶	Power controller board com. failed
4046¶	AOC model does not match
4047¶	AOC was disconnected
4101¶ 4102¶ 4103¶ 4104¶	DET#n TCD overcurrent detected	n=1 to 4
4105¶ 4106¶ 4107¶ 4108¶	DET#n FTD overcurrent detected	n=1 to 4
4109¶ 4110¶ 4111¶ 4112¶	DET#n flame is out	n=1 to 4
4121¶ 4122¶ 4123¶ 4124¶	DET#n FPD cooling fan error	n=1 to 4
4125¶ 4126¶ 4127¶ 4128¶	DET#n FPD overcurrent detected	n=1 to 4
4129¶ 4130¶ 4131¶ 4132¶	DET#n BID short-circuit in discharge cell	n=1 to 4
4133¶ 4134¶ 4135¶ 4136¶	DET#n DTCD overvoltage detected in cell power	n=1 to 4
4149¶ 4150¶ 4151¶ 4152¶	DET#n FTD adjustment failed	n=1 to 4
4201¶	TCD signal was out of range
4203¶ 4204¶ 4205¶ 4206¶	DET#n ignition failed.	n=1 to 4
4207¶	H2, AIR APC are not ready
4208¶ 4209¶ 4210¶ 4211¶	DET#n failed to start plasma	n=1 to 4
4212¶	DCG APC are not ready
4213¶	DCG flow rate is not enough
4301¶	Settings were changed
4302¶	Program time error	The analysis can be performed even after this message is displayed, however, the program finishes after 9999.99 minutes elapses.
4303¶	Clean up program time error	The analysis can be performed even after this message is displayed, however, the program finishes after 9999.99 minutes elapses.
4304¶	Pre-Run program time error	The analysis can be performed even after this message is displayed, however, the program finishes after 9999.99 minutes elapses.
4305¶	Clean up program start error
5006¶ 5007¶ 5008¶ 5070¶ 5071¶ 5072¶ 5101¶ 5105¶	CARx calc. prss out of range	x=1 to 4
5009¶ 5010¶ 5011¶ 5073¶ 5074¶ 5077¶ 5078¶ 5102¶ 5106¶ 5107¶ 5110¶ 5111¶	CARx calc. flow out of range	x=1 to 4
5042¶ 5043¶ 5044¶ 5067¶ 5068¶ 5069¶ 5103¶ 5104¶	CARn septum purge calculated pressure out of range	n=1 to 4
5075¶ 5076¶ 5108¶ 5109¶	CARm calc. ratio out of range	m=1 to 4
5112¶	Analysis waiting
6001¶ 6023¶	AOCm rack error	m=1 to 2 1: Main AOC 2: Sub AOC
6002¶ 6024¶	AOCm syringe error	m=1 to 2 1: Main AOC 2: Sub AOC
6003¶ 6025¶	AOCm plunger error	m=1 to 2 1: Main AOC 2: Sub AOC
6004¶ 6026¶	AOCm can not start	m=1 to 2 1: Main AOC 2: Sub AOC
6005¶ 6027¶	AOCm RAM initialized	m=1 to 2 1: Main AOC 2: Sub AOC
6006¶ 6028¶	AOCm ROM error	m=1 to 2 1: Main AOC 2: Sub AOC
6007¶ 6029¶	AOCm CH2 command error	m=1 to 2 1: Main AOC 2: Sub AOC
6008¶ 6030¶	AOCm sample vial is not set	m=1 to 2 1: Main AOC 2: Sub AOC
6009¶ 6031¶	AOCm RAM error	m=1 to 2 1: Main AOC 2: Sub AOC
6010¶ 6032¶	AOCm installation error	m=1 to 2 1: Main AOC 2: Sub AOC
6011¶ 6033¶	AOCm CH1 error	m=1 to 2 1: Main AOC 2: Sub AOC
6012¶ 6034¶	AOCm CH2 error	m=1 to 2 1: Main AOC 2: Sub AOC
6013¶ 6035¶	AOCm waste vial is not set	m=1 to 2 1: Main AOC 2: Sub AOC
6014¶	AOC-20s rotating error
6015¶	AOC-20s expansion and control error
6016¶	AOC-20s up/down error
6017¶	AOC-20s can not start
6018¶	AOC-20s vial setting error
6019¶	AOC-20s vial returning error
6020¶	AOC-20s holding error
6021¶	AOC-20s sample vial removed
6022¶	AOC-20s vial is not set
6036¶ 6041¶	AOCm solvent vial is not set	m=1 to 2 1: Main AOC 2: Sub AOC
6037¶ 6042¶	AOCm L2 vial is not set	m=1 to 2 1: Main AOC 2: Sub AOC
6038¶ 6043¶	AOCm L3 vial is not set	m=1 to 2 1: Main AOC 2: Sub AOC
6039¶ 6044¶	AOCm turret step out	m=1 to 2 1: Main AOC 2: Sub AOC
6040¶ 6045¶	AOCm vial sensor error	m=1 to 2 1: Main AOC 2: Sub AOC
6101¶	SCD furnace temperature sensor is down
6103¶	SCD furnace temperature sensor error
6104¶	SCD furnace temperature exceeds the limit
6105¶	SCD furnace temperature controller error
6106¶	SCD furnace temperature set point not reached
6111¶	SCD furnace abs. press fell below lower limit
6112¶	SCD furnace abs. press was exceeded upper limit
6113¶	SCD exhaust for vacuum error
6121¶	SCD fan error
6122¶	SCD ozonier voltage was exceeded upper limit
6123¶	SCD ozonier voltage fell below lower limit
6124¶	SCD PSU-24V error
6135¶	SCD thermistor temperature exceeds the limit
6141¶	SCD thermistor error
6142¶	SCD H2 solenoid valve has been fixed to ON
6143¶	SCD furnace leak error
6144¶	SCD detector leak error
6145¶	SCD AD converter initialization was failed
6146¶	SCD oxygen primary pressure is not enough
6147¶	SCD hydrogen primary pressure is not enough
6148¶	SCD WDT error
6149¶	SCD heater relay has been fixed to ON
6151¶	SCD flow controller#1 was not connected
6152¶	SCD flow controller#2 was not connected
6154¶	SCD PMT light was leaked
6155¶	SCD furnace temperature is low
6156¶	SCD ozonizer oxygen flow is low
6163¶	SCD hydrogen control irregularity
6164¶	SCD hydrogen was overpressure
6167¶	SCD nitrogen control irregularity
6168¶	SCD nitrogen was overpressure
6171¶	SCD furnace oxygen control irregularity
6172¶	SCD furnace oxygen was overpressure
6175¶	SCD ozone source oxygen control irregularity
6176¶	SCD ozone source oxygen was overpressure
6177¶	SCD flow controller#1 error
6178¶	SCD flow controller#2 error
6181¶	DET#4 SCD overcurrent detected
9000¶	COL CRG use time warning
9002¶	Fan use time warning
9004¶ 9005¶ 9006¶ 9052¶	CARx septum counter warning	x=1 to 4
9007¶ 9008¶ 9009¶ 9053¶	CARx insert counter warning	x=1 to 4
9010¶	System is not ready
9011¶	Ignition finished(retried)
9012¶ 9013¶ 9014¶ 9015¶ 9016¶ 9017¶ 9018¶ 9019¶ 9024¶	xxx sensor use time warning	xxx=COL, INJ1, DET1, INJ2, DET2, AUX3, AUX4, AUX5, SAT
9020¶	Temp. is not controlled
9021¶	Detector is not controlled
9054¶	Processing, unable to start
9055¶ 9056¶ 9057¶ 9058¶	PURn is not controlled	n=1 to 4
9059¶ 9060¶	AOCm syringe counter warning	m=1 to 2
9061¶	Not execute this operation
9062¶	Prep run wait time elapsed
9063¶ 9064¶ 9065¶ 9066¶	CARx prim is out of range	x=1 to 4
9071¶	SCD vacuum pump use time warn.
9072¶	SCD ozone scrub. use time warn.
9073¶	SCD in pyrotube use time warn
9074¶	SCD out pyrotube use time warn.
9075¶	SCD furnace temp sensor warn.
9076¶	SCD induc. tube use time warn.
9077¶	SCD furnace abs. press warning
9078¶	SCD unable to auto start
9079¶	SCD detector abs. press is high
9080¶	SCD detector abs. press is low
9081¶	The dual AOC version does not match with each other
9082¶	H2 sensor is not enabled
9084¶	Power controller board failed to read parameter.

Error Message

1¶

2¶

5¶

6¶

7¶

8¶

9¶

10¶

11¶

12¶

53¶

54¶

13¶

14¶

15¶

16¶

23¶

24¶

25¶

26¶

27¶

28¶

29¶

30¶

31¶

32¶

35¶

38¶

39¶

40¶

51¶

59¶

62¶

65¶

68¶

71¶

74¶

60¶

63¶

66¶

69¶

72¶

75¶

61¶

64¶

67¶

70¶

73¶

76¶

77¶

78¶

79¶

80¶

81¶

82¶

83¶

84¶

85¶

86¶

87¶

88¶

89¶

91¶

92¶

100¶

101¶

102¶

103¶

104¶

105¶

106¶

107¶

108¶

109¶

110¶

112¶

113¶

116¶

117¶